description t he acpl-w611/acpl-p611 is an optically coupled gate that combines a gaasp light emitting diode and an integrated high gain photo detector. the output of the detector ic is an open collector schottky clamped transistor. the internal shield provides a guaranteed c ommon mode transient immunity specification of 10,000 v/ s for the acpl-w611. t his unique design provides maximum ac and dc circuit isolation while achieving ttl compatibility. the optocoupler ac and dc operational parameters are guaranteed from -40 c to +85 c allowing trouble-free system performance. t he acpl-w611/acpl-p611 is suitable for high speed logic interfacing, input/output buffering, as line re c eivers in environments that conventional line receivers cannot tolerate and are recommended for use in extremely high ground or induced noise environments. fea tures 10 kv/ s minimum common mode rejection (cmr) at vcm = 1000 v high speed: 10 mbd typical lsttl/ttl compatible ? ow input current capability: 5 ma ? uaranteed ac and dc performance over temperature: -40 c to +85 c ? tretched so-6 package ?af ety approval: ul recognized: 3750 v rms for 1 minute and 5000 v rms* for 1 minute per ul1577?pending approval csa: pending approval iec/en/din en 60747-5-2: pending approval applications ? solated line receiver ? omputer-peripheral interfaces ? icroprocessor system interfaces ? igital isolation for a/d, d/a conversion ? witching power supply instrument input/output isolation ? r ound loop elimination ? ulse transformer replacement ? ower transistor isolation in motor drives ? solation of high speed logic systems f unctional diagram a 0.1 f bypass capacitor must be connected between pins v cc and gnd. caution: it is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by esd. a cpl-w611/acpl-p611 high cmr, high speed ttl compatible optocoupler data sheet 1 2 3 6 5 4 cathode gnd v cc v o acpl-w611/acpl-p611 anode led on off output l h truth table (positive logic) shield
2 schematic diagram ordering information specify part number followed by option number (if desired). example: a cpl-w611- x x xe 000 = standard ss0-6 package, 100 per tube. 500 = tape and reel packaging option. 060 = iec/en/din en 60747-5-2, v iorm = 630 v peak xx xe = lead free option. option data sheets available. contact avago technologies sales representative, authorized distributor, or visit our web site at http://www.avagotech.com/optocouplers . shield 6 5 4 1+ 3 v f i f i cc v cc v o gnd i o acpl-w60l
3 p ackage outline drawings acpl-w611 stretched so-6 package a cpl-p611 stretched so-6 package 4.580 (0.180) 45 0.381 (0.015) 1.270 (0.050) 0.200 0.100 (0.008 0.004) 0.450 (0.018) 0.750 (0.0295) 11.500 0.300 (0.453 0.012) 6.807 (0.268) dimensions in millimeters and (inches). coplanarity = 0.10 mm (0.004 inches). 7 12.650 (0.498) land pattern recommendation 3.180 (0.125) 1.590 (0.063) 7 1.905 (0.075) 3 2 1 4 5 6 0.760 (0.030) 4.580 (0.180 ) +0.254 0 +0.010 -0.000 0.38 0.127 (0.015 0.005) 1.27 (0.050) bsg 0.20 0.10 (0.008 0.004) 0.450 (0.018) 1 0.250 (0.040 0.010) 9.7 0.250 (0.382 0.010) 6.81 (0.268) 7.62 (0.300) dimensions in millimeters and (inches). coplanarity = 0.10 mm (0.004 inches). 7.00 7.00 10.7 (0.421) land pattern recommendation 3.180 0.127 (0.125 0.005) 1.590 0.127 (0.063 0.005) 7 7 2.16 (0.085) 3 2 1 4 5 a detail a 6 0.20 (0.008) 45.00
4 recommended solder reflow thermal profile recommended pb-free ir profile regulatory information the acpl-w611 and acpl-p611 is pending approval by the following organizations: i ec/en/din en 60747-5-2 (option 060 only) approval under: iec 60747-5-2 :1997 + a1:2002 en 60747-5-2:2001 + a1:2002 din en 60747-5-2 (vde 0884 teil 2):2003-01 ul approval under ul 1577, component recognition program up to v iso = 3750 v rms . file e55361. csa approval under csa component acceptance notice #5, f ile ca 88324. note: use of non chlorine-activated fluxes is highly recommended. note: use of non chlorine-activated fluxes is highly recommended. 0 time (seconds) temperature ( c) 200 100 50 150 100 200 250 300 0 30 sec. 50 sec. 30 sec. 160 c 140 c 150 c peak temp. 245 c peak temp. 240 c peak temp. 230 c soldering time 200 c preheating time 150 c, 90 + 30 sec. 2.5 c 0.5 c/sec. 3 c + 1 c/?.5 c tight typical loose room temperature preheating rate 3 c + 1 c/?.5 c/sec. reflow heating rate 2.5 c 0.5 c/sec. 217 c ramp-down 6 c/sec. max. ramp-up 3 c/sec. max. 150 - 200 c 260 +0/-5 c t 25 c to peak 60 to 150 sec. 20-40 sec. time within 5 c of actual peak temperature t p t s preheat 60 to 180 sec. t l t l t smax t smin 25 t p time temperature notes: the time from 25 c to peak temperature = 8 minutes max. t smax = 200 c, t smin = 150 c
5 insulation and safety related specifications pa ra meter symbol acpl-p611 acpl-w611 units conditions m inimum external air gap l(101) 7 8 mm measured from input (external clearance) terminals to output terminals, shortest distance through air. m inimum external tracking l(102) 8 8 mm measured from input terminals (external creepage) to output terminals, shortest distance path along body. m inimum internal plastic gap 0.08 0.08 mm through insulation distance (internal clearance) conductor to conductor, usually the straight line distance thickness between the emitter and detector. t racking resistance cti 175 175 v din iec 112/vde 0303 part 1 (comparative tracking index) isolation group iiia iiia material group (din vde 0110, 1/89, table 1) iec/en/din en 60747-5-2 insulation characteristics* (acpl-w611/ acpl-p611 option 060) description symbol characteristic unit installation classification per din vde 0110/1.89, table 1 f or rated mains voltage 150 v rms i ?iv f or rated mains voltage 300 v rms i ?iii f or rated mains voltage 600 v rms i ?ii climatic classification 55/100/21 p ollution degree (din vde 0110/1.89) 2 m aximum working insulation voltage v iorm 630 v peak input to output test voltage, method b* v iorm x 1.875=v pr , 100% production test with t m = 1 sec, v pr 1181 v peak pa r tial discharge < 5 pc input to output test voltage, method a* v iorm x 1.5=v pr , t ype and sample test, t m = 60 sec, partial discharge < 5 pc v pr 945 v peak highest allowable overvoltage (transient overvoltage t ini = 10 sec) v iotm 6000 v peak sa fe t y-limiting values ?m aximum values allowed in the event of a failure. case temperature t s 175 c input current** i s, input 230 ma output power** p s, output 600 mw insulation resistance at ts, v io = 500 v r s >10 9 ? power output ?p s (mw), input current ?i s (ma) 0 0 t s ?case temperature ? c 200 175 50 400 125 25 75 100 150 600 200 100 300 500 700 p s (mw) i s (ma) *r efer to the optocoupler section of the isolation and control c omponents designer s catalog, under product safety regula- tions section, (iec/en/din en 60747-5-2) for a detailed description of method a and method b partial discharge test profiles. ** refer to the following figure for dependence of p s and i s on ambient temperature.
6 absolute maximum ratings pa ra meter symbol min. max. units storage temperature t s -55 125 c operating temperature t a -40 85 c av erage input current i f(avg) 20 ma reverse input voltage v r 5v input power dissipation p i 45 mw supply voltage (1 minute maximum) v cc 7v output collector current i o 50 ma output collector voltage v o 7v output collector power dissipation p o 85 mw l ead solder temperature t ls 260 c for 10 sec. solder reflow temperature profile see package outline drawings section recommended operating conditions pa ra meter symbol min. max. units input current, low level i fl 0 250 a input current, high level i fh 515ma po w er supply voltage v cc 4.5 5.5 v operating temperature t a - 40 85 c f an out (at r l = 1 k ? )n 5t tl loads output pull-up resistor r l 330 4k ? electrical specifications (dc) ov er recommended operating conditions unless otherwise specified. all typicals at v cc = 5 v, t a = 25 c. pa ra meter symbol min. typ. max. units test conditions fig. note high level output current i oh 5.5 100 av cc = 5.5 v, 1 v o = 5.5 v, i f = 250 a input threshold current i th 2.0 5.0 ma v cc = 5.5 v, v o = 0.6 v, 13 i ol > 13 ma lo w level output voltage v ol 0.35 0.6 v v cc = 5.5 v, i f = 5 ma, 2, 4, i ol(sinking) = 13 ma 5,13 high level supply current i cch 47.5mav cc = 5.5 v, i f = 0 ma, lo w level supply current i ccl 6 10.5 ma v cc = 5.5 v, i f = 10 ma, input forward voltage v f 1.4 1.5 1.75 v t a = 25 c i f = 10 ma 3 1.3 1.8 input reverse breakdown voltage bv r 5vi r = 10 a input capacitance c in 60 pf f = 1 mhz, v f = 0 v input diode temperature ? v f / ? t a -1.6 mv/ ci f = 10 ma 12 co efficient all typicals at t a = 25 c, v cc = 5 v
7 s witching specifications (ac) ov er recommended operating conditions t a = -40 c to 85 c, v cc = 5 v, i f = 7.5 ma unless otherwise specified. all typicals at v cc = 5 v, t a = 25 c. pa ra meter symbol min. typ. max. units test conditions fig. note pr opagation delay time to t plh 20 48 75 ns t a = 25 cr l = 350 ? ,5 high output level 100 c l = 15 pf pr opagation delay time to t phl 25 50 75 ns t a = 25 c6 lo w output level 100 p ulse width distortion |t phl - t plh |3.535nsr l = 350 ? ,10 c l = 15 pf pr opagation delay skew t psk 40 ns 10, 11 output rise time (10%-90%) t r 24 ns output fall time (10%-90%) t f 10 ns output high level common |cm h |10 1 5 kv/ sv cc = 5 v, i f = 0 ma, mode transient immunity v o(min) = 2 v, r l = 350 ? , t a = 25 c, v cm = 1000 v 7, 9 output low level common |cm l |10 1 5 kv/ sv cc = 5 v, i f = 7.5 ma, 8, 9 mode transient immunity v o(max) = 0.8 v, r l = 350 ? , t a = 25 c, v cm = 1000 v p ackage characteristics all typicals at t a = 25 c. pa ra meter symbol min. typ. max. units test conditions fig. note input-output insulation v iso 3750 v rms rh < 50% for 1 min. 3, 4 t a = 25 c input-output resistance r i-o 10 12 ? v i-o = 500 v 3 input-output capacitance c i-o 0.6 pf f = 1 mhz, t a = 25 c3 notes: 1. bypassing of the power supply line is required with a 0.1 f ceramic disc capacitor adjacent to each optocoupler. the total lead length between both ends of the capacitor and the isolator pins should not exceed 10 mm. 2. p eaking circuits may produce transient input currents up to 50 ma, 50 ns maximum pulse width, provided average current does n ot e xc eed 20 ma. 3. de vice considered a two terminal device: pins 1, 2 and 3 shorted together, and pins 4, 5 and 6 shorted together. 4. in accordance with ul 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 v rms for 1 second (leakage detection current limit, i i-o 5 a). 5. t he t plh propagation delay is measured from 3.75 ma point on the falling edge of the input pulse to the 1.5 v point on the rising edge of the output pulse. 6. t he t phl propagation delay is measured from 3.75 ma point on the rising edge of the input pulse to the 1.5 v point on the falling edge of the output pulse. 7. cm h is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., v out > 2.0 v). 8. cm l is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., v out > 0.8 v). 9. f or sinusoidal voltages, (|dv cm |/dt) max = f cm v cm(p-p) . 10. see application section; ?ropagation delay, pulse-width distortion and propagation delay skew for more information. 11. t psk is equal to the worst case difference in t phl and/or t plh that will be seen between units at any given temperature within the worst case operating condition range.
8 figure 5. low level output current vs. temperature figure 4. output voltage vs. forward input current figure 1. high level output current vs. temperature figure 2. low level output voltage vs. temperature figure 3. input diode forward characteristic figure 6. test circuit for t phl and t plh i oh ?high level output current ? a -60 0 t a ?temperature ? c 100 10 15 -20 5 20 v cc = 5.5 v v o = 5.5 v i f = 250 a 60 -40 0 40 80 v cc = 5.5 v i f = 5.0 ma 0.5 0.4 -60 -20 20 60 100 t a ?temperature ? c 0.3 80 40 0 -40 0.1 v ol ?low level output voltage ?v 0.2 i o = 16 ma i o = 12.8 ma i o = 9.6 ma i o = 6.4 ma v f ?forward voltage ?volts 10 0.1 0.01 1.10 1.20 1.30 1.40 i f ?forward current ?ma 1.60 1.50 1.0 0.001 100 i f v f + t a = 25 c 1 6 2 3 4 5 1234 5 6 i f ?forward input current ?ma r l = 350 ? r l = 1 k ? r l = 4 k ? 0 0 v cc = 5 v t a = 25 c v o ?output voltage ?v i ol ?low level output current ?ma -60 0 t a ?temperature ? c 100 60 80 -20 20 20 v cc = 5.0 v v ol = 0.6 v 60 -40 0 40 80 40 i f = 10 ma, 15 ma i f = 5.0 ma output v o monitoring node 1.5 v t plh t phl i f input v o output i f = 7.5 ma i f = 3.75 ma +5 v i f r l r m 0.1 f bypass *c l *c l is approximately 15 pf which includes probe and stray wiring capacitance. input monitoring node pulse gen. z o = 50 ? t f = t r = 5 ns v cc gnd 1 3 6 5 4
9 f igure 12. temperature coefficient for forward voltage vs. input current f igure 10. rise and fall time vs. temperature f igure 9. pulse width distortion vs. temperature f igure 8. propagation delay vs. pulse input current f igure 7. propagation delay vs. temperature f igure 11. test circuit for common mode transient immunity and typical wa ve forms v cc = 5.0 v i f = 7.5 ma 100 80 -60 -20 20 60 100 t a ?temperature ? c 60 80 40 0 -40 0 t p ?propagation delay ?ns 40 20 t plh , r l = 4 k ? t plh , r l = 1 k ? t plh , r l = 350 ? t phl , r l = 350 ? 1 k ? 4 k ? v cc = 5.0 v t a = 25 c 105 90 5913 i f ?pulse input current ?ma 75 15 11 7 30 t p ?propagation delay ?ns 60 45 t plh , r l = 4 k ? t plh , r l = 1 k ? t plh , r l = 350 ? t phl , r l = 350 ? 1 k ? 4 k ? v cc = 5.0 v i f = 7.5 ma 40 30 -20 20 60 100 t a ?temperature ? c 20 80 40 0 -40 pwd ?pulse width distortion ?ns 10 r l = 350 k ? r l = 1 k ? r l = 4 k ? 0 -60 -10 t r , t f ?rise, fall time ?ns -60 0 t a ?temperature ? c 100 300 -20 40 20 60 -40 0 40 80 60 290 20 v cc = 5.0 v i f = 7.5 ma r l = 4 k ? r l = 1 k ? r l = 350 ? , 1 k ? , 4 k ? t rise t fall r l = 350 ? dvf/ dt ?forward voltage temperature coefficient ?mv/ c 0.1 1 10 100 i f ?pulse input current ?ma -1.4 -2.2 -2.0 -1.8 -1.6 -1.2 -2.4 v o 0.5 v v o (min.) 5 v 0 v switch at a: i f = 0 ma switch at b: i f = 7.5 ma v cm cm h cm l v o (max.) v cm (peak) v o +5 v 0.1 f bypass + _ 350 ? v ff 1 3 6 5 4 b a output v o monitoring node i f pulse generator z o = 50 ? v cc gnd
figure 13. input threshold current vs. temperature i th ?input threshold current ?ma -60 0 t a ?temperature ? c 100 4 5 -20 2 20 60 -40 0 40 80 3 v cc = 5.0 v v o = 0.6 v 1 r l = 4 k ? r l = 1 k ? r l = 350 ? 6 for product information and a complete list of distributors, please go to our website: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies limited in the united states and other countries . data subject to change. copyright ? 2006 avago technologies limited. all rights reserved. av01-0208en june 15, 2006
|
